Boat Classes

Rowing Boat Rigging: Pitch, Span and Oarlock Height

Rigging sets how the oars sit in the boat. Learn what pitch, span and oarlock height mean, why they matter and how to check them safely.

On this page
  1. The short answer
  2. Pitch
  3. Span and spread
  4. Oarlock height
  5. Why rigging matters
  6. Setting up rigging
  7. Checking your rigging safely
  8. Sweep and sculling rigs

The short answer

Rigging is how the oars, oarlocks and riggers are set up on the boat. Three measurements do most of the work. Pitch describes how the blade sits as it enters and moves through the water. Span (or spread in sculling) is the distance between oarlocks. Oarlock height is how high the oarlock sits above the seat or the gunwale. There is no single correct set of numbers. The boat maker’s settings are the starting point, and a coach adjusts them for the boat and the rower.

Pitch

In simple terms, pitch is the angle of the blade relative to the water. It affects how cleanly the blade enters at the catch and how it leaves at the finish. It is set through the oarlock and the position of the oar in the gate, so small changes to the oarlock or the oar’s position change the pitch. Boat builders and clubs do not always define pitch in exactly the same way, so check your boat’s manual before you adjust it.

Span and spread

Span is usually the distance between the oarlocks of neighboring rowers along a sweep boat. Keeping span even along the boat helps the crew work together, since each rower’s stroke is set against the same reference. Spread is the sculling equivalent: the distance between the two oarlocks a sculler uses, measured across the boat. Definitions of these measurements can vary, so the boat maker’s guide is the best reference for how your boat measures them.

Oarlock height

Oarlock height is the vertical position of the oarlock above the seat or gunwale. It affects how deep the blade sits in the water and how high the handle sits in relation to the rower’s body. Because it changes both blade depth and handle height at once, adjust it in small steps and check the effect on the water, not just on the bank.

Why rigging matters

Rigging affects how the boat feels and how the blades behave. Settings that are too high or too low can make blades enter too shallow or too deep, which can cause a blade to skip out early (washing out) or catch in the water (a crab). Uneven settings across the boat can make it harder to keep level. Good rigging also helps comfort, reach and the rower’s ability to feather the blade cleanly in the recovery.

Setting up rigging

Start from the boat maker’s rigging guide, since it gives the manufacturer’s starting values. Then make your changes gradually:

  • Set the boat level before you measure, so the readings are reliable.
  • Measure each oarlock position from the same reference points, and record the numbers.
  • Change one thing at a time, then row a short session and note how the boat feels.
  • Ask a coach to watch the blades enter and leave the water, since the bank view is more reliable than your own sense from the seat.

A tape measure and a spirit level are enough for basic checks. Keep a written record of your settings, so you can go back to a setting that worked.

Checking your rigging safely

Loose or worn rigging can fail during a stroke, which is a serious risk. Before every session:

  • Check that every nut, pin and fitting is tight and has no play.
  • Look for cracks, wear or bending in the oarlocks, gates, riggers and pins.
  • Replace any worn or damaged part before you row. Don’t row with a loose or cracked fitting.
  • Ask a coach or the boat builder if you are not sure a part is safe.

Sweep and sculling rigs

In a sweep boat, the oarlocks sit on alternating sides, and the span between neighboring rowers matters most. In a sculling boat, each sculler has two oarlocks, one on each side, so the spread between them matters more than span. Both rigs use the same basic parts, but the layout and the measurements differ, so use the manual for your boat type.

For the basic setup of a single scull, including rigging checks, see how to row a single scull. For the parts and costs of rigging a boat you own, see how much a single rowing boat costs. For the difference between sweep and sculling in general, see sculling vs sweep rowing, and for the rigging words you’ll hear on the water, see common terms used in rowing.

The complete guide to boat classes

Sculling vs Sweep Rowing: Boat Classes Explained
Read the guide

Keep exploring

Guides from other topics

All topics →