The Murph is a CrossFit hero workout named for Navy Lieutenant Michael Murphy, who was killed in action in Afghanistan. It is long and demanding, and it has no official rowing version. This guide shows how to swap its two mile runs for rows, split the strength work into manageable sets, and scale the session so it is safe.
What the Murph is
The original Murph is a one-mile run, 100 pull-ups, 200 push-ups, 300 air squats and another one-mile run, usually done in a weighted vest (often around 20 lb, though people use lighter vests). It is a common benchmark for cardio and muscular endurance, and many gyms run it on Memorial Day as a tribute to service members. It is designed to be hard, so it isn’t a first workout for most people.
Why swap the runs for rows
Running the Murph is hard on the legs and joints, and it’s not an option for everyone. A rowing version keeps the same two cardio blocks and the same strength work, but the erg is lower impact and easier to pace and log. Rowing also shifts the load away from the calves and shins and towards the legs, back and arms. The strength work doesn’t change, so the session stays demanding.
A rowing Murph: the set-up
There is no official rowing version, so pick your distances and write them down. A common swap is a 1,600 m row (close to a mile) in place of each run.
- Warm up for about 10 minutes on the erg with easy rowing and a few build-up strokes.
- Row 1,600 m at a controlled pace. Don’t sprint the first piece, since the strength work comes straight after.
- Complete the strength work in sets (see the next section).
- Row 1,600 m again, aiming to hold the same effort as the first piece, or slightly harder if you feel strong.
- Cool down for about 5 minutes with easy rowing and light stretching.
Log your total time and note the distances. A rowing Murph time is only comparable to other rowing Murph times if the distances match.
Pacing the strength work
Doing 100 pull-ups, 200 push-ups and 300 squats in one block is very hard. Break them into sets you can repeat with good form. For example, 5 rounds of 20 pull-ups, 40 push-ups and 60 squats gives the full total. Use short rests, but don’t rush the reps. Good form is the priority, and sloppy reps often cost more time than a short rest does.
The legs are usually tired after the first row, so the squats can feel harder than expected. Keep the squats smooth and controlled, with full depth, and drive through your heels.
Scaling it
- Half Murph: halve every component (800 m rows, 50 pull-ups, 100 push-ups, 150 squats), with no vest. This is a good first attempt.
- Pull-ups: use banded or jumping pull-ups, or a lat pulldown if you have one. Keep the movement controlled.
- Push-ups: perform them from the knees or on a raised surface.
- Squats: reduce the depth or the number of reps, or use a bench as a target.
- Vest: leave it off until the full workout is comfortable.
Safety
Warm up before starting, especially your shoulders, hips and back. Build up gradually. If you are new to rowing, a first Murph is a poor place to learn the stroke, so use the rowing machine workouts guide to build your base first. Don’t add a vest if you have back or shoulder issues.
Stop and get help if you feel chest pain, dizziness, faintness or unusual breathlessness, or if a shoulder, elbow or back problem sharpens during the pull-ups or rows. Check with a doctor first if you have a heart condition, high blood pressure or a recent injury.
Where it fits in your training
The Murph is a benchmark, not a weekly session. Do it no more than once every few weeks, and allow two or three easy days after it. Between attempts, keep building the base with rowing interval WODs and strength training for rowing, which cover the pulling and leg work that the Murph tests. For a shorter circuit that uses bodyweight moves alongside the erg, see rowing HIIT circuits. Stretch after the session with the routine in stretching for rowers.