What a split is
A split is the time it takes to row 500 metres. On an erg, the monitor shows it as minutes, seconds and tenths, followed by “/500m”. A split of 2:00.0 means 500 metres in two minutes. A lower number is a faster pace. A split of 1:50 is faster than 2:00, and 2:10 is slower.
Split is the standard way to talk about pace on indoor rowers, and the Concept2 pace calculator uses the same unit. Most other erg monitors show it too.
Real-time split and average split
The monitor shows two splits:
- Real-time split is the pace you would hold if the stroke you just took continued. It changes with every stroke. It reacts quickly to a strong drive or a rushed recovery, so it is noisy.
- Average split is the mean pace for the whole piece so far. It settles down over time, so it is the better figure for judging how a piece is going.
Use the real-time figure for form feedback, and the average for pacing decisions.
Convert a split into a race time
Because a split is time per 500 metres, the finish time for any distance is simple arithmetic. Multiply the split by the number of 500 m blocks in the distance:
- 1,000 m = 2 × split
- 2,000 m = 4 × split
- 6,000 m = 12 × split
| Split | 1,000 m | 2,000 m | 6,000 m |
|---|---|---|---|
| 1:30 | 3:00 | 6:00 | 18:00 |
| 1:45 | 3:30 | 7:00 | 21:00 |
| 2:00 | 4:00 | 8:00 | 24:00 |
| 2:15 | 4:30 | 9:00 | 27:00 |
| 2:30 | 5:00 | 10:00 | 30:00 |
If your split is 1:45 for the whole piece, your 2,000 m time is 7:00. A piece with a mix of splits averages to the overall time, so check the total time and total distance to get the average split: time ÷ distance × 500.
Why a faster split takes much more power
Speed and power are not linked in a straight line. On an erg, the monitor’s power figure (watts) rises much faster than the speed does, because drag on the boat or the flywheel grows quickly with speed. Concept2’s power formula scales with the cube of speed. In practice, dropping your split by a few seconds takes a clear step up in effort. Do not expect a small change in split to come from a small change in effort.
What counts as a good split
There is no single good split. Benchmarks depend on sex, age, body weight, experience and the piece length. A 2:00 split is a solid target for many recreational rowers, but experienced and competitive rowers are much faster. Use your own history first: a split you can hold for a piece you have done before tells you more than a table does.
Use a split to set a target
For a race piece or a test, pick a target split you have held in training, then plan the start and the middle:
- Start a little slower than the target, or at the target for the first 250 to 500 metres, then settle into it. Starting too fast is the most common mistake.
- Hold the target through the middle. This is where the piece gets hard and the pace starts to slip.
- Finish strong if you have something left. Many rowers can push the last 250 to 500 metres.
Practice the target on a steady piece of similar length before you use it in a test. The 6K erg test guide shows how this applies to a longer piece. If you are working out the time for a 5K, the 5K time guide uses the same arithmetic.
Common mistakes
- Flying and dying. Starting far too fast, then falling off the target. Settle earlier.
- Chasing the real-time number. A single stroke can look fast or slow for reasons that are not about pace. Watch the average.
- Changing the damper mid-piece, which changes how the machine feels and makes the split harder to compare.
- Forgetting the piece length. A split that works for 500 metres may be too fast for 2,000.